This is exactly what it says: a SR Latch that I made in 345/2/4 (otherwise known as "Star Wars"). I used guns (for input), reflectors, duplicators, eaters, and NOR gates (duh).

Code: Select all

```
#CXRLE Pos=-192,-16
x = 259, y = 177, rule = 345/2/4
147.A97.A$146.3A95.3A$147.A97.A2$151.A89.A$150.3A87.3A$151.A89.A3$
226.A2.B$225.5A.BA$226.A.A.2A$226.A2.A.2A.A$6.C218.7A.2A$6.A219.A3.A.
A.2A$5.A.BA155.A67.A.A.AC$3.5A155.3A65.4AB$4.A2.2AC154.A66.C.A.A$.A.A
.3A225.C$.B3A2.AC7.A$2.A.2A8.4A.CBA21.CBA21.CBA21.CBA21.CBA21.CBA21.C
BA$BA.2A9.B.A2.CBA21.CBA21.CBA21.CBA21.CBA21.CBA21.CBA27.A$.2A.A10.CB
A174.3A$.A2.A188.A35.BA$6A187.A34.C.A$.A2.A187.3A33.B3A$193.A34.A.A$
193.A$192.3A34.2C4.A$193.A35.2B3.3A$193.A35.2A4.A$192.3A30.CBA7.A$
193.A31.CBA7.2A$235.A$235.A$151.A25.CBA21.CBA21.CBA6.3A$150.3A24.CBA
21.CBA21.CBA7.A$151.A2$147.A$146.3A$147.A7$137.A$136.3A$137.A$233.A$
141.A87.A2.3A$140.3A85.3A.2A$141.A87.A3.A$232.3A$233.A4$222.A2.A2.A$
221.9A$93.A128.A5.A$92.3A127.A5.A$93.A127.2A5.2A$93.A128.A4.2A$93.2A
127.A3.2A$93.A127.6A30.A$93.A128.A2.A30.3A$92.3A162.A$93.A$253.A$141.
A110.3A$140.3A110.A$141.A2$137.A$136.3A$137.A20$137.A$136.3A$137.A2$
141.A$140.3A98.A$141.A98.3A$241.A$93.A$92.3A150.A$93.A128.A2.A18.3A$
93.A127.6A18.A$93.2A127.A3.2A$93.A128.A4.2A$93.A127.2A5.2A$92.3A127.A
5.A$93.A128.A5.A$221.9A$222.A2.A2.A4$233.A$232.3A$141.A87.A3.A$140.3A
85.3A.2A$141.A87.A2.3A$233.A$137.A$136.3A$137.A7$147.A$146.3A$147.A2$
151.A$150.3A24.CBA21.CBA21.CBA7.A$151.A25.CBA21.CBA21.CBA6.3A$235.A$
235.A$193.A31.CBA7.2A$192.3A30.CBA7.A$193.A35.2A4.A$193.A35.2B3.3A$
192.3A34.2C4.A$193.A$193.A34.A.A$.A2.A187.3A33.B3A$6A187.A34.C.A$.A2.
A188.A35.BA$.2A.A10.CBA174.3A$BA.2A9.B.A2.CBA21.CBA21.CBA21.CBA21.CBA
21.CBA21.CBA27.A$2.A.2A8.4A.CBA21.CBA21.CBA21.CBA21.CBA21.CBA21.CBA$.
B3A2.AC7.A$.A.A.3A225.C$4.A2.2AC154.A66.C.A.A$3.5A155.3A65.4AB$5.A.BA
155.A67.A.A.AC$6.A219.A3.A.A.2A$6.C218.7A.2A$226.A2.A.2A.A$226.A.A.2A
$225.5A.BA$226.A2.B3$151.A101.A$150.3A99.3A$151.A101.A2$147.A109.A$
146.3A107.3A$147.A109.A!
```

The guns are on the left and the NOR gates are on the right (hint: they look like the guns)

Remove the top gun and this is what you get.

As you can see, you can remove the lower gun and it will stay the same.

Now I replace the upper gun. Notice that it has not yet entered the NOR gate.

Now the upper gun output has been through the entire course.

Once again, I remove the gun and it stays the same.

On a lesser note, I also built a NAND gate. I didn't use it for this, but I will likely use it to build an adder:

Code: Select all

```
x = 41, y = 124, rule = 345/2/4
31.C$31.A$29.AB.A$30.5A$28.C2A2.A$28.B.3A.A.A$21.A8.A2.3AB$20.3A7.B3A
.A$21.A7.CA2.2A.AB$33.A.2A$33.A2.A$32.6A$33.A2.A5$10.A2.A2.A$9.9A$10.
A5.A3$10.2A2.2A$10.2B2.2B$10.2C2.2C46$10.2A$10.2B$10.2C22$14.2A$14.2B
$14.2C22$10.2A2.2A$10.2B2.2B$10.2C2.2C!
```